Results 1 to 7 of 7

Hybrid View

  1. #1
    Join Date
    Sep 2013
    Posts
    1

    Default Old lock set hole

    I have a old doors I wish to use but the locksets are only 2" from the edge and can't be reused. How can I redrill over the existing hole to handle the newer locksets.

  2. #2
    Join Date
    Jun 2007
    Location
    Fayette County, Ohio
    Posts
    6,053

    Default Re: Old lock set hole

    You need to either install a plug the same size as the existing hole or inlayed patches on both sides.
    You can get router inlay kits from any wood working store. Here is a link to a video demo of router inlay www.woodworking******.com/2007/03/05/podcast-14-router-inlays/
    Inthe link above replace the ****** with o n l i n e with out the spaces

    Jack
    Last edited by JLMCDANIEL; 09-11-2013 at 12:03 PM.
    Be sure you live your life, because you are a long time dead.-Scottish Proverb

  3. #3
    Join Date
    May 2008
    Location
    Pacific Northwet
    Posts
    1,901

    Default Re: Old lock set hole

    You can also use a repair/reinforcement shield.

    http://www.amazon.com/s/ref=nb_sb_no...ine+reinforcer



    I didn't say it would look pretty.
    The "Senior Member" designation under my name doesn't mean I know a lot, it just means I talk a lot.I've been a DIYer since I was 12 (thanks, Dad!). I have read several books on various home improvement topics. I do not have any current code books I can refer to. I was an apprentice plumber for two years.

  4. #4
    Join Date
    Aug 2007
    Posts
    8,065

    Default Re: Old lock set hole

    You say the existing locksets are 2" from the edge, but this is irrelevant, what is the center line of the existing hole? The reason that this is important is that old locks tend to have a smaller diameter hole, so adjusting a small hole for a new lockset may be possible without any modifications to the door.

    Current locksets use a 1-3/8" set back for interiors and 1-3/4" set back for exterior doors. Set back is the distance from the edge of the door to the center line of the lockset.

    To redrill a door, you make yourself a jig by making a "horseshoe" of 1x6 over both sides of the door and the edge. You clamp this horseshoe over the existing hole, mark your setback from the edge of the door. Drill the new hole with the recommended sized hole saw, which is generally 2" (resulting in a 2-1/4" hole ), verify the requirements of the new lock/handset before you drill.
    I suffer from CDO ... Its like OCD, but in alphabetical order, LIKE IT SHOULD BE!!!

  5. #5
    Join Date
    May 2008
    Location
    Pacific Northwet
    Posts
    1,901

    Default Re: Old lock set hole

    Quote Originally Posted by A. Spruce View Post
    Current locksets use a 1-3/8" set back for interiors and 1-3/4" set back for exterior doors. Set back is the distance from the edge of the door to the center line of the lockset.
    Spruce, I think you mean 2+3/8" and 2+3/4", respectively. The thickness of the doors is typically 1+3/8" and 1+3/4". I believe the hole for the lockset is 2+1/8" diameter.

    That is, the center of the hole is positioned according to these measurements. If you have at least 1+5/16" between the edge of the door and the existing hole, you can rebore 2+1/8" hole at a 2+3/8" backset without any problems.

    Spruce's horseshoe trick is to make something out of wood similar to the metal bracket I posted earlier, and use this as a guide for the hole saw to enlarge/reposition the hole. (It's not necessary to make the hole in the horseshoe before attaching to the door, but doing so will make it easier to align it to the door.) You may also need to enlarge the bolt hole; old style are around 3/4 or 7/8"; the newer ones require a 15/16" hole. (I think. You'll want to double-check the bolt hole measurement.)
    Last edited by Fencepost; 09-12-2013 at 05:56 PM.
    The "Senior Member" designation under my name doesn't mean I know a lot, it just means I talk a lot.I've been a DIYer since I was 12 (thanks, Dad!). I have read several books on various home improvement topics. I do not have any current code books I can refer to. I was an apprentice plumber for two years.

  6. #6
    Join Date
    Aug 2007
    Posts
    8,065

    Default Re: Old lock set hole

    Quote Originally Posted by Fencepost View Post
    Spruce, I think you mean 2+3/8" and 2+3/4", respectively. The thickness of the doors is typically 1+3/8" and 1+3/4". I believe the hole for the lockset is 2+1/8" diameter.
    What, is accuracy really necessary?

    Yes, you are correct, I did, indeed, mean 2-3/8" and 2-3/4" as the setback. I did say to verify the measurement requirements of the new lock sets, which also includes the diameter of the hole.
    I suffer from CDO ... Its like OCD, but in alphabetical order, LIKE IT SHOULD BE!!!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •