• ##### Contests and Sweepstakes

1. Junior Member
Join Date
Jul 2010
Posts
1

## Sue52

I am trying to install chair railing (2 1/2") on wall going down a stair wall (no wainscotting). problen is wall is straight for 16" then angles down to follow line of stairs.I cannot figure out how to match the angle with the straight edge plus the chair rail has a pattern to it.Any help greatly appreciated befor I lose my mind thanks

2. ## Re: Sue52

You determine the degree of angle change, say 45* for example, and divide by 2 which is 22.5*. You'd cut the end of each piece at 22.5*. Probably the easiest way to figure out the true angle would be to have a helper hold one uncut piece in place while you hold the other and mark the top and bottom of each piece where they overlap.

3. Junior Member
Join Date
Jan 2011
Posts
4

## Re: Sue52

Hey sue - what you are describing is not like the average 45 or 22 1/2 degrees like you would expect - i would use a "sliding t-bevel to copy the exact angle and then transfer it to your miter saw - this will make it easier to find the angle (no need to know the exact angle quantity then) - have fun with the moulding

4. Senior Member Rank 2
Join Date
Sep 2009
Location
florida
Posts
598

## Re: Sue52

This tool will find and give you the cuts needed. There should be a smaller 10"version of the tool being lanuched this week on Amazon.

http://www.amazon.com/QUINT-GRAPHICS...4366483&sr=8-1
Last edited by Gizmo; 01-06-2011 at 09:18 PM. Reason: link wouldnt open

5. Senior Member Rank 2
Join Date
Sep 2009
Location
florida
Posts
598

## Re: Sue52

Sue52,The pictures I posted are just to give you an idea how to find your miter angle cuts with the MMP tool or any other brand tool.
I placed the tool on an existing stair hand rail, its the same concept you will need with the chair railing.
The 1st & 3rd pic's are at the botton & top of the stair. The 2nd and 4th are close ups indicating the desired saw setting in the reciprocal window of the tool.

Good Luck

6. ## Re: Sue52

what everyone has forgotten is the 1st step, layout the chair rail line on the wall first.

detereming the height of it then make a level line on the walls where it will run level. bring this line over to the nosing of the top of the landing, then do the same at the lower floor, from there you need 2 people, snap a chalk line from these two points, these lines are what you will use to determine the angle from. from there use a angle finder and go at it

i have attached a couple pics from a house i trimmed out a few years back with a similar detail

7. Senior Member Rank 2
Join Date
Sep 2009
Location
florida
Posts
598

## Re: Sue52

Good point jkirk, I guess we all figured the layout was pretty much a common practice before anything else.

Nice work by the way in the pics I see there are accute "Miter" angles that could really confuse a novice........
Last edited by Gizmo; 01-07-2011 at 07:53 PM.

8. Senior Member Rank 2
Join Date
Sep 2009
Location
florida
Posts
598

## Re: Sue52

Originally Posted by Gizmo
Sue52,The pictures I posted are just to give you an idea how to find your miter angle cuts with the MMP tool or any other brand tool.
I placed the tool on an existing stair hand rail, its the same concept you will need with the chair railing.
The 1st & 3rd pic's are at the botton & top of the stair. The 2nd and 4th are close ups indicating the desired saw setting in the reciprocal window of the tool.

Good Luck

The 10" Miter Master Plus was " Finally" just launched on Amazon.

http://www.amazon.com/T110-MITER-MAS...4871316&sr=8-4

#### Posting Permissions

• You may not post new threads
• You may not post replies
• You may not post attachments
• You may not edit your posts
•