+ Reply to Thread
Results 1 to 10 of 11

Hybrid View

  1. #1
    Join Date
    Jan 2009
    Posts
    2

    Default Draws to much Power

    Recently when my water pump for my cistern (holding tank)comes on
    it draws enough juice to turn off the computer on a separate line. It has happened in the passed but periodically and never for the length of time it has been doing it lately.
    I have reduced the number of loads (other equipment) on the line to no avail.
    The water pump has always draw a lot of power. Enough to dim the lights for a brief second. I replaced the switch on the water pump about a year ago so i know its fairly new.
    The water pump is on a line with a single light & switch only.
    The computer is on a line with 4 other receptacles.
    I have an 100 amp service and the home is roughly 40 yrs old.
    I have not added any new line in more then 3 years time period.
    Any suggestions on what maybe causing the pump to draw more power now then in the past?

    Any help would be greatly appreciated.

  2. #2
    Join Date
    Jun 2007
    Location
    Fayette County, Ohio
    Posts
    5,803

    Default Re: Draws to much Power

    First just because it's on a different line doesn't mean it's not not on the same phase, so indirectly it may be on the same line. High resistance connections (corroded perhaps) could be a problem or it could just be time for a new pump.
    Jack
    Be sure you live your life, because you are a long time dead.-Scottish Proverb

  3. #3
    Join Date
    Jan 2009
    Posts
    2

    Red face Re: Draws to much Power

    Thanks Jack for the help, it is appreciated.

    I have map out the loads on each line within the fuse box with a night light. I have determined that the pump is on a separate line by itself. Also two fuses (lines) are empty.
    How does one test for the phasing issue?
    I checked the pump wiring both at the pump and the fuse box and all seems to be fine with no corrosion seen. I also plugged the pump into another circuit with only one load and the problem of the pump still drawing a lot of power still occurs.
    How does one know if the pump needs replacing or if there is corrosion of the wiring?

  4. #4
    Join Date
    Jun 2007
    Location
    Fayette County, Ohio
    Posts
    5,803

    Default Re: Draws to much Power

    With a volt meter. If you chose one line and check the voltage between it and each of the others. If the voltage reads 0 it is on the same phase if it reads 220 that line is on the other phase.

    One thing you might want to try, if the motor is a capacitor start motor. It will probably have a can on it like the one pictured on top of this motor It may be getting weak. You should be able to get a replacement at a store like Grangers. Be sure to turn of the power and discharge the capacitor by shorting across the lead with an insulated screw driver so you don't get zapped. It may also have a centrifugal switch that switches from start to run windings. If it's the problem you should notice the pump running at low speed for and extended period of time which will cause it to draw excessive power. The centrifugal switch can be replaced but should be done by someone who knows what they are doing. It might be just as cheap to replace the motor.
    Jack
    Be sure you live your life, because you are a long time dead.-Scottish Proverb

  5. #5
    Join Date
    Jun 2007
    Location
    Fayette County, Ohio
    Posts
    5,803

    Default Re: Draws to much Power

    Actually before someone else jumps in and corrects me, it's not a seperate phase it's a seperat leg of a single phase .
    Jack
    Be sure you live your life, because you are a long time dead.-Scottish Proverb

  6. #6
    Join Date
    Feb 2009
    Posts
    693

    Talking Re: Draws to much Power

    Quote Originally Posted by JLMCDANIEL View Post
    Actually before someone else jumps in and corrects me, it's not a seperate phase it's a seperat leg of a single phase .
    Jack

    Jesh, Jack..... There is A RAT in in separate...... Learn to spell. LOL

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •